OBD Manual diagnostic on Honda Vigor without obd tools

OBD HACK HONDA VIGOR 1990-1994

OBD Manual diagnostic on Honda Vigor without obd tools

The Honda Vigor was a premium sedan that was sold in Japan through the Honda Verno dealer network from 1981 to 1995 derived from the Honda Accord, and briefly sold in North America from 1992 to 1994 as the Acura Vigor. Early Vigors were more upmarket versions of the Accord and served as Honda’s flagship until the arrival of the Honda Legend. In 1989, the Vigor would differentiate itself further from the Accord with unique styling and an available longitudinal five-cylinder engine, and a twin to the Vigor was introduced with the Honda Inspire, available at Honda Clio dealerships.

It was replaced in North America with the Acura TL and in Japan with the Honda Saber/Inspire, which were the same vehicle sold through different networks.

The Vigor was developed during what was known in Japan as the Japanese asset price bubble or “bubble economy”.

 

 

PLEASE SELECT THE OBD SOCKET OF YOUR CAR BELOW AND FOLLOW THE JUMPER SETTINGS.

HONDA PIN MANUAL DIAGNOSTICYear range: 1989 to 2001

Locations: Under the passengers seat.
Above the passengers side kick panel.
In the center console.

honda obd hack manual diagnostic

Year range: 1998 to 2009

Locations: Under the drivers side dash panel.
Inside or below the glovebox.

PLEASE FOLLOW THE JUMPER SETTING ABOVE:

PLEASE NOTE:If after following the instructions below the Check Engine Light does not flash it either means there are no fault codes or there is a connection error. To test connection, remove the TPS and run the engine then recheck codes.



INSTRUCTION:
1. If possible run the engine to bring the oxygen sensor up to operating temperature then switch the engine off.
2. Connect the terminals using your own jumper wire, as shown in the diagram above.
3. Turn ignition ON, the Check Engine Light (CEL) should be flashing on your car dashboard.
READ CHECK ENGINE ON HONDA DASHBOARD
4. Read codes as described in the Code Format Description below.
Code Format Diagram

read honda trouble code without scan tool

READING CODE INSTRUCTION
• Each code is made up of two series of flashes.
• The long flashes indicate the ‘tens’ digits.
• The short flashes indicate the ‘ones’ digits.
• A long pause separates each code sequence.
• Code Format Diagram shows above is code No. 12.
• If nolongflashes are observed then the code is a straight count of short flashes. i.e. 4 flashes = code 4.
LIST OF TROUBLE CODE
Code 0 and 11 Electronic Control Module (ECM)
Code1 Heated oxygen sensor A
Code 2 Oxygen content B
Code 3 and 5 Manifold Absolute Pressure
Code 4 Crank position sensor
Code 6 Engine coolant temperature
Code 7 Throttle position sensor
Code 8 Top dead center sensor
Code 9 No.1 cylinder position sensor
Code 10 Intake air temperature sensor
Code 12 Exhaust recirculation system
Code 13 Barometric pressure sensor
Code 14 Idle air control valve or bad ECM
Code 15 Ignition output signal
Code 16 Fuel Injector
Code 17 Vehicle speed sensor
Code 19 A/T lock-up control solenoid
Code 20 Electric load detector
Code 21 V-TEC control solenoid
Code 22 V-TEC pressure solenoid
Code 23 Knock sensor
Code 30 A/T FI signal A
Code 30 A/T FI signal B
Code 41 Heated oxygen sensor heater
Code 43 Fuel supply system
Code 45 Fuel supply metering
Code 48 Heated oxygen sensor
Code 61 Front heated oxygen sensor
Code 63 Rear heated oxygen sensor
Code 65 Rear heated oxygen sensor heater
Code 67 Catalytic converter system
Code 70 Automatic transaxle
Code 71 Misfire detected cylinder 1
Code 72 Misfire detected cylinder 2
Code 73 Misfire detected cylinder 3
Code 74 Misfire detected cylinder 4
Code 75 Misfire detected cylinder 5
Code 76 Misfire detected cylinder 6
Code 80 Exhaust recirculation system
Code 86 Coolant temperature
Code 92 Evaporative emission control system

Erasing procedure.

  • After the faults have been rectified, trouble codes can be erased by using a Scan Tool connected to the data link connector (DLC) or as follows:
  • Switch ignition OFF.
  • Remove radio fuse (7.5A) from underhood fusebox for 10 seconds minimum
  • Reinstall fuse.
  • Repeat checking procedure to ensure no data remains in ECM fault memory.

NEVERMIND THE TAGS BELOW.

Related Topics  Toyota Startlet 1996-1999 Obd1-Diy Diagnostic Tutorial

Leave a Reply

Your email address will not be published. Required fields are marked *