Crown Victorial TPMS Reset Guide

WITH STANDARD IGNITION: 1. Inflate all tires to pressure listed on tire placard. 2. Turn ignition to OFF position and press and release brake pedal. 3. Cycle ignition from OFF to RUN position 3 times, ending in RUN position. 4. Press and release brake pedal. 5. Turn ignition to OFF position. 6. Cycle ignition from OFF to RUN position 3 times, ending in RUN position. 7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. Place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires. 8. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, the training procedure must be repeated. **WITH INTEGRATED KEY FOB (ACTUAL KEY CONTAINED IN KEY FOB) PUSH-BUTTON START: 1. With vehicle off, press and release the brake pedal. 2. Using the push button, press and hold the button until the vehicle is in accessory mode (ACC mode). WARNING: DO NOT PUSH AND RELEASE TOO QUICKLY…PUSH--WAIT FOR SOUND--RELEASE. 3. Power off by pushing the button 1 time. 4. Repeat 2 more times, ending in ACC mode. 5. Press and release the brake pedal, then turn vehicle off. 6. Using the push button, press and hold the button until the vehicle is in accessory mode. 7. Power off by pushing the button 1 time. 8. Repeat 2 more times, ending in ACC mode. 9. Horn will sound once the TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. 10. Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires. 11. After successfully programming the LR tire, the message center should display "TRAINING COMPLETE." 12. Inflate all tires to pressure listed on tire placard. ***WITH INTELLIGENT ASSIST IGNITION SYSTEM (NO ACTUAL KEY CONTAINED IN KEY FOB): 1. With vehicle off, press and release the brake pedal. 2. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off. 3. Repeat 2 more times, ending in ACC mode. 4. Press and release the brake pedal, then turn vehicle off. 5. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off. 6. Repeat 2 more times, ending in ACC mode. 7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. 8. Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires. 9. After successfully programming the LR tire, the message center should display "TRAINING COMPLETE." 10. Inflate all tires to pressure listed on tire placard.

Crown Victorial TPMS Reset Guide

The Ford Crown Victoria (or simply Crown Vic) is a rear-wheel drive full-sized four-door sedan that was marketed and manufactured by Ford from the 1992 to the 2011 model years over two generations. Discontinued in 2011, the latter day Crown Victoria began production in 1991 at Ford’s St. Thomas Assembly plant in Southwold, Ontario, Canada. Dropping its previous LTD prefix, Ford instead revived a nameplate once used on a two-door version of the Fairlane sold in the North American market for the 1955 model year.

The Crown Victoria shared the Ford Panther platform and major powertrain, body, and suspension components with the Lincoln Town Car and Mercury Grand Marquis. Along with its rebadged Mercury and Lincoln variants, the Crown Victoria was the final full-frame rear-wheel-drive passenger sedan produced in North America. The durability associated with its layout popularized the Crown Victoria with taxicab owners and commonly used police patrol/pursuit vehicles in North America.

WITH STANDARD IGNITION:
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to OFF position and press and release brake pedal.
3. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
4. Press and release brake pedal.
5. Turn ignition to OFF position.
6. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. Place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
8. After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, the training procedure must be repeated.

**WITH INTEGRATED KEY FOB (ACTUAL KEY CONTAINED IN KEY FOB) PUSH-BUTTON START:
1. With vehicle off, press and release the brake pedal.
2. Using the push button, press and hold the button until the vehicle is in accessory mode (ACC mode). WARNING: DO NOT PUSH AND RELEASE TOO QUICKLY…PUSH–WAIT FOR SOUND–RELEASE.
3. Power off by pushing the button 1 time.
4. Repeat 2 more times, ending in ACC mode.
5. Press and release the brake pedal, then turn vehicle off.
6. Using the push button, press and hold the button until the vehicle is in accessory mode.
7. Power off by pushing the button 1 time.
8. Repeat 2 more times, ending in ACC mode.
9. Horn will sound once the TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE.
10. Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
11. After successfully programming the LR tire, the message center should display “TRAINING COMPLETE.”
12. Inflate all tires to pressure listed on tire placard.

Related Topics  Ford Taurus TPMS Reset and Relearn Tutorial

***WITH INTELLIGENT ASSIST IGNITION SYSTEM (NO ACTUAL KEY CONTAINED IN KEY FOB):
1. With vehicle off, press and release the brake pedal.
2. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
3. Repeat 2 more times, ending in ACC mode.
4. Press and release the brake pedal, then turn vehicle off.
5. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
6. Repeat 2 more times, ending in ACC mode.
7. Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE.
8. Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
9. After successfully programming the LR tire, the message center should display “TRAINING COMPLETE.”
10. Inflate all tires to pressure listed on tire placard.

Leave a Reply

Your email address will not be published. Required fields are marked *