Category BMW TPMS Reset

BMW F06 F12 F13 M6 coupé TPMS Reset Guide

Post Content

BMW F06 F12 F13 M6 coupé TPMS Reset Guide

BMW F06 F12 F13 M6 coupé  TPMS Tire Pressure Monitoring System Reset Guide

Illuminated: the Tire Pressure Monitor signals a loss of tire inflation pressurein a tire. Reduce your speed and stop cautiously. Avoid sudden braking and steering maneuvers. Flashing and then continuously illuminated: no flat tire or loss of tire inflation pressure can be detected.
▷ Interference through systems or devices
with the same radio frequency: after leav‐
ing the area of the interference, the system
automatically becomes active again.
▷ TPM could not conclude the reset: perform
the reset of the system again.
▷ A wheel without TPM electronics is fitted:
have the service center check it if needed.
▷ Malfunction: have the system checked by
your service center

Reset the system after each adjustment of the
tire inflation pressure and after every tire or
wheel change.
On the Control Display and on the vehicle:
1. “Vehicle info”
2. “Vehicle status”
3.
  “Perform reset”
4. Start the engine – do not drive off.
5. Reset tire inflation pressure:”Perform
reset”.
6. Drive away.

The tires are shown in gray and the status is
displayed.
After driving faster than 19 mph/30 km/h for a
short period, the set tire inflation pressures are
accepted as reference values. The reset is
completed automatically while driving.
After a successfully completed Reset, the
wheels on the Control Display are shown in
green and “Tire Pressure Monitor (TPM)
active” is displayed.
You may interrupt this trip at any time. When
you continue the reset resumes automatically.

TPMS Reset BMW TPMS Reset Guide

BMW TPM S RESET GUIDE

Post Content

BMW TPM S RESET GUIDE
BMW TPM S RESET GUIDE

BMW AG is a Germany-based company which currently produces automobiles and motorcycles, and produced aircraft engines until 1945.

The company was founded in 1916 and has its headquarters in Munich, Bavaria. BMW produces motor vehicles in Germany, Brazil, China, India, South Africa and the United States. In 2015, BMW was the world’s twelfth largest producer of motor vehicles, with 2,279,503 vehicles produced.[3] The Quandt family are long-term shareholders of the company, with the remaining stocks owned by public float.

Automobiles are marketed under the brands BMW (with sub-brands BMW M for performance models and BMW i for plug-in electric cars), Mini and Rolls-Royce. Motorcycles are marketed under the brand BMW Motorrad.

The company has significant motorsport history, especially in touring cars, Formula 1, sports cars and the Isle of Man TT.

TPMS Reset BMW TPMS Reset Guide

BMW Z Series 2011-2014 TPMS Reset
BMW Z Series 2011-2014 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 1 Series 2008-2013 TPMS RESET
BMW 1 Series 2008-2013 TPMS RESET
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 2 Series 2014 tpms reset
BMW 2 Series 2014 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 3 Series 2012-2015 TPMS Reset
BMW 3 Series 2012-2015 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW I8 2014-2015 TPMS Reset Guide
BMW I8 2014-2015 TPMS Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW I3 2014-2015 TPMS Reset Guide
BMW I3 2014-2015 TPMS Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW Alpina 2004-2014 TPMS Reset
BMW Alpina 2004-2014 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 7 Series 2015 tpms reset
BMW 7 Series 2015 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 7 Series 2011-2014 tpms reset
BMW 7 Series 2011-2014 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 7 Series 2006-2011 tpms reset
BMW 7 Series 2006-2011 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 6 Series E63 E64 645Ci F06 F12 F13 640i 2006-2015 TPMS Reset Guide
BMW 6 Series E63 E64 645Ci F06 F12 F13 640i 2006-2015 TPMS Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 5 Series 2015 tpms reset
BMW 5 Series 2015 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 5 Series 2011-2014 tpms reset
BMW 5 Series 2011-2014 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 5 Series 2006-2011 tpms reset
BMW 5 Series 2006-2011 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 4 Series 2014-2015 tpms reset
BMW 4 Series 2014-2015 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 4 Series E92 E93 F32 F33 F36 2013-2015 TPMS Reset Guide
BMW 4 Series 2014 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 3 Series 2007-2011 tpms reset
BMW 3 Series 2007-2011 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 3 Series 4 door – sedan tpms reset 2014
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW 3 Series 2 door -wagon 2012-2013 tpms reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW Z Series 2007-2011 TPMS Reset
BMW Z Series 2007-2011 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X6 2015 TPMS Reset
BMW X6 2015 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X6 2011-2014 TPMS Reset
BMW X6 2011-2014 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X6 2008-2011 TPMS Reset
BMW X6 2008-2011 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X5 2014-2015 TPMS Reset
BMW X5 2014-2015 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X5 2011-2013 TPMS Reset
BMW X5 2011-2013 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X5 2007-2011 TPMS Reset
BMW X5 2007-2011 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X4 2015 TPMS Reset Guide
BMW X4 2015 TPMS Reset Guide 

IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

BMW X3 2006-2014 TPMS Reset
BMW X3 2006-2014 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X3 2006-2014 TPMS Reset
BMW X3 2006-2014 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW X1 2013-2015 TPMS Reset Guide
BMW X1 2013-2015 TPMS Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW M6 2011-2014 TPMS Reset
BMW M6 2011-2014 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW M6 2006-2011 TPMS Reset
BMW M6 2006-2011 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW M5 2006-2011 TPMS Reset Guide
BMW M5 2006-2011 TPMS Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
BMW M3 2008-2013 TPMS Reset
BMW M3 2008-2013 TPMS Reset
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select “Settings” or “Vehicle Info”.
4. Select “Vehicle”, “Vehicle/Tires” or “Vehicle Status”.
5. Select “TPM”, “Reset TPM”, or “Perform Reset”.
6. Start the engine, select “Reset”, “Yes”.
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and “RESET” are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until “RESETIING” or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.
IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

bmw tpms reset button,bmw tpms reset tool,bmw reset tpms light,bmw x3 tpms reset,bmw x5 tpms reset,bmw 328i tpms reset,bmw x1 tpms reset,bmw e60 tpms reset,bmw f30 tpms reset,2006 bmw tpms reset,bmw tpms reset,bmw z4 tpms reset button,tpms bmw e90 reset,bmw e46 tpms reset,bmw e92 tpms reset,bmw e70 tpms reset,bmw f10 tpms reset,bmw how to reset tpms,bmw idrive tpms reset,2008 bmw 328i tpms reset inactive,bmw mini tpms reset,bmw m3 tpms reset,bmw motorcycle tpms reset,2009 bmw m3 tpms reset,bmw tpms not resetting,bmw tpms will not reset,reset tpms on bmw x3,reset tpms on bmw,reset tpms on bmw x5,bmw tpms sensor reset,bmw 1 series tpms reset,bmw 3 series tpms reset,bmw 5 series tpms reset,bmw tpms won’t reset,reset tpms bmw x6,2008 bmw x5 tpms reset,2006 bmw x5 tpms reset,2011 bmw x5 tpms reset,2012 bmw x5 tpms reset,2015 bmw x1 tpms reset,2009 bmw x5 tpms reset,bmw z4 tpms reset,2003 bmw z4 tpms reset,2004 bmw z4 tpms reset,2005 bmw z4 tpms reset,06 bmw tpms reset,08 bmw tpms reset,05 bmw tpms reset,09 bmw 328i tpms reset,06 bmw x5 tpms reset,05 bmw 530i tpms reset,04 bmw x3 tpms reset,06 bmw 530i tpms reset,07 bmw x5 tpms reset,bmw 135i tpms reset,bmw 120d tpms reset,2010 bmw 128i tpms reset,2008 bmw 135i tpms reset,2011 bmw 128i tpms reset,11 bmw 328i tpms reset,2008 bmw tpms reset,2011 bmw tpms reset,2005 bmw tpms reset,2009 bmw tpms reset,2014 bmw tpms reset,2015 bmw tpms reset,2006 bmw 330i tpms reset,2004 bmw 530i tpms reset,2010 bmw 328i tpms reset,bmw 335i tpms reset,bmw 320d tpms reset,bmw 335xi tpms reset,bmw 325i tpms reset,2011 bmw 328i tpms reset,2005 bmw 325ci tpms reset,2008 bmw 335xi tpms reset,2007 bmw 3 series tpms reset,2010 bmw 3 series tpms reset,2008 bmw 3 series tpms reset,2014 bmw 3 series tpms reset,bmw 525i tpms reset,2011 bmw 535i tpms reset,2005 bmw 525i tpms reset,2005 bmw 545i tpms reset,2008 bmw 550i tpms reset,2008 bmw 535xi tpms reset,2005 bmw 5 series tpms reset,bmw 650i tpms reset,2006 bmw 650i tpms reset,reset tpms bmw 750li,2007 bmw 750li tpms reset